Context Plus XFP501/X/CON XFP Networkable Single Loop 32 Zone Panel

♦ Context plus XFP501/X/CON Addressable Control Panel
♦ Third-party certificated to EN54 parts 2 and 4 by the LPCB.
♦ Full compatibility
♦ InterConnect Up To Eight XFP Main Panels
♦ Four XFP Repeater Panels Per Main Two Wire RS485 Network.
♦ Two Independently Programmable Conventional Sounder Circuits.
♦ Two Programmable Inputs.
♦ A Fault Output Relay & Three Programmable Relay Outputs With Voltage
♦ Three Zone Dependency Functions (A, B & C to EN54-2 Clause 7.12)
♦ A Day/Night Function.
♦ An Investigation Delay Period Function.
♦ Individual Sensitivity Settings For Each Device
♦ Powerful Short Circuit Protected Loop Drivers
♦ An Integral EN54 Switch Mode PSU rated @ 185-260V a.c. 50/60Hz (3A on 32 zone panel, 1.4A on 16 zone panel)
♦ Earth Fault Monitoring
♦ 12 Months Warranty


Context Plus XFP501/X/CON

BRAND Context Plus
Model XFP501/X/CON
Main supply 230V a.± 10% 50/60Hz. Max current 680mA
Internal power supply 27V d.c Nominal
Total output current limited to 3A @ 230 V a.c.
Supply and battery charger monitored for failure Yes
Batteries monitored for disconnection and failure yes
Batteries protected against deep discharge yes
Max. battery size and type 7.0 Ahr VRLA
Specified batteries for LPCB approved systems 2 x Yuasa NP7-12
Quiescent current drain (1 loop unloaded) < 80mA
Quiescent current drain (2 loop unloaded) <100mA
Earth fault monitoring Yes (any conductor)
Temperature compensated charging Yes
Number of loop drivers (XFP501/CON) 2 (XFP502/CON
Line monitored for open and short circuit faults Yes
Onboard loop isolators with LED indication when active Yes
Auto-polling from each loop en Yes
Max. loop output current 500mA (Voltage: 25V min, 34V max)
Max. number of addressable devices per loop 126
Number of programmable sounder groups 16
Number of programmable output sets 16
Number of programmable circuits 2
End of line resistor value Yes
End of line resistor value 6800 Ω 5% Tol. 0.25 W
Line monitored for open and short circuit faults Yes
Outputs fused at 400mA
Max. number of sounders @ 20mA 80
Type Relay voltage free single pole changeover
Max switching current 1A
Max switching voltage 30 V d.c
Fault Active when no faults are present
‘24V’ Aux Power Output 19.5V min, 28V max. Max current 100mA. Protected by resettable overload circuit
Input 1 Connectto 0V to trigger. Max input voltage 27V d.c. (non-latching). Programmable from cause and effect.
Input 2 Connectto 0V to trigger. Max input voltage 27V d.c (non-latching). Programmable from cause and effect.
Mains Fuse 1A HRC Ceramic 20mm
Battery Fuse – limits the current drawn from the battery 3.15A F 20mm
Control buttons Silence, Reset, Resound, Investigate; More Information; Menu
Event scrolling and menu access buttons Up (1); Down (2); Accept (3); Abort (4)
Liquid Crystal Display Two lines x 40 characters, backlit
Number of Zonal LED indicators 32
Approx. dimensions of back box (W x H x D 410 x 250 x 80mm (metal)
Approx. dimensions of lid (W x H x D) 439 x 274 x 7mm (metal)
Approx. weight (without batteries) 4.5kg
Type of cable Fire resistant screened cable, minimum size 1mm2
Max. cable length per loop 1km
Connector blocks Plug-on type, largest acceptable conductor size 1.5mm2
Max. allowable loop impedance (each conductor 20Ω
Max. cable capacitance .27µF
Connection Via AFP711 network driver card fitted at main panel
Temperature range -5 to +40oC
Maximum relative humidity 95%
Warranty 12 Months

[porto_recent_products view=”grid”]